FISH-Fluorescent in situ hybridization

FISH-Fluorescent in situ hybridization

FISH (Fluorescent in situ hybridization) is a cytogenetic technique that can be used to detect and localize the presence or absence of specific DNA sequences on chromosomes. It uses fluorescent probes that bind to only those parts of the chromosome with which they show a high degree of sequence similarity. Fluorescence microscopy can be used to find out where the fluorescent probe bound to the chromosome. FISH is often used for finding specific features in DNA. These features can be used in genetic counseling, medicine, and species identification.

Probes are often derived from fragments of DNA that were isolated, purified, and amplified for use in the Human Genome Project. The size of the human genome is so large, compared to the length that could be sequenced directly, that it was necessary to divide the genome into fragments. The fragments were added into a framework that made it possible to use bacteria to replicate the fragments. The fragments were put into order by analyzing size-exclusion separation of enzymatically-digested fragments. Clonal populations of bacteria, each population maintaining a single artificial chromosome, are stored in various laboratories around the world. The artificial chromosomes (BAC) can be grown, extracted, and labeled, in any lab. These fragments are on the order of 100 thousand base-pairs, and are the basis for most FISH probes.

Preparation and Hybridization Process

Scheme of the principle of the FISH Experiment to localize a gene in the nucleus.

First, a probe is constructed. The probe must be large enough to hybridize specifically with its target but not too large to impede the hybridization process. The probe is tagged directly with fluorophores, with targets for antibodies or with biotin. Tagging can be done in various ways, for example nick translation and PCR using tagged nucleotides.

Then, an interphase or metaphase chromosome preparation is produced. The chromosomes are firmly attached to a substrate, usually glass. Repetitive DNA sequences must be blocked by adding short fragments of DNA to the sample. The probe is then applied to the chromosome DNA and incubated for approximately 12 hours while hybridizing. Several wash steps remove all un-hybridized or partially-hybridized probes. The results are then visualized and quantified using a microscope that is capable of exciting the dye and recording images.

If the fluorescent signal is weak, amplification of the signal may be necessary in order to exceed the detection threshold of the microscope. Florescent signal strength depends on many factors such as probe labeling efficiency, the type of probe, and the type of dye. Fluorescently-tagged antibodies or streptavidin are bound to the dye molecule. These secondary components are selected so that they have a strong signal.

Variations on Probes and Analysis

FISH is a very general technique. It is often arbitrarily divided into more specific categories based on application, however each category is similar in that, in a chemical sense, the technique is the same; hybridization is the common denominator. The differences between the various FISH techniques are usually due to the construction and content of the fluorescently-labeled DNA probe. The size, overlap, colour, and mixture of the probes make possible all FISH techniques.

Probe size is important because longer probes hybridize more specifically than shorter probes. The overlap defines the resolution of detectable features. If the goal of an experiment is to detect the breakpoint of a translocation, then the overlap of the probes — the degree to which one DNA sequence is contained in the adjacent probes — defines the minimum window in which the breakpoint occurs.

The mixture of probes determines the type of feature the probe can detect. Probes that hybridize along an entire chromosome are used to count the number of a certain chromosome, show translocations, or identify extra-chromosomal fragments of chromatin. This is often called "whole-chromosome painting." If every possible probe is used, every chromosome, (in essence the whole genome) would be marked fluorescently, which would not be particularly useful for determining features of individual sequences. A mixture of smaller probes can be created that are specific to a particular region (locus) of DNA; these mixtures are used to detect deletion mutations. When combined with a specific colour, a locus-specific probe mixture is used to detect very specific translocations. Special locus-specific probe mixtures are often used to count chromosomes, by binding to the centromeric regions of chromosomes, which are unique enough to identify each chromosome (with the exception of Chromosome 13, 14 21, 22.)

Because modern microscopes can detect a range of colours in fluorescent dyes each human chromosome can be identified (M-FISH) using whole-chromosome probe mixtures and a variety of colours. There are currently twice as many chromosomes than fluorescent dye colours. However, ratios of probe mixtures can be used to create additional colours. As with comparative genomic hybridization, the probe mixture for the secondary colours is created by mixing the correct ratio of two sets of differently-labeled probes for the same chromosome. Differently coloured probes can be used for the detection of translocations. Several techniques exploit the resolution limitations of microscopes to resolve spatial distributions of dye below a few hundred nanometers. Colours that are adjacent appear to overlap, and a secondary colour is observed.

In reciprocal translocations, where both breakpoints are known, locus-specific probes are made for it and part of the region one either side of breakpoint. In normal cells, two colours will be visible; in diseased cells such as those found in BCR/ABL translocations, the two dye colours overlap, and a third colour is observed. This technique is known as double-fusion FISH or D-FISH. In translocations where only one of the breakpoints is known or constant, locus-specific probes are made for one side of the breakpoint and the other intact chromosome. In normal cells, the secondary colour is observed, but only the primary colour is observed when the translocation occurs. This technique is known as "break-apart FISH".

Medical applications

Often parents of children with a developmental delay want to know more about their child's conditions before choosing to have another child. These concerns can be addressed by analysis of the parents' and child's DNA. In cases where the child's developmental delay is not understood, the cause of it can be determined using FISH and cytogenetic techniques. Examples of diseases that are diagnosed using FISH include Prader-Willi syndrome, Angelman syndrome, 22q13 deletion syndrome, chronic myelogenous leukemia, acute lymphoblastic leukemia, Cri-du-chat, Velocardiofacial syndrome, and Down syndrome.

In medicine, FISH can be used to form a diagnosis, to evaluate prognosis, or to evaluate remission of a disease, such as cancer. Treatment can then be specifically tailored. A traditional exam involving metaphase chromosome analysis is often unable to identify features that distinguish one disease from another, due to subtle chromosomal features; FISH can elucidate these differences. FISH can also be used to detect diseased cells more easily than standard Cytogenetic methods, which require dividing cells and requires labor and time-intensive manual preparation and analysis of the slides by a technologist. FISH, on the other hand, does not require living cells and can be quantified automatically, a computer counts the fluorescent dots present. However, a trained technologist is required to distinguish subtle differences in banding patterns on bent and twisted metaphase chromosomes

Species identification

FISH is often used in clinical studies. If a patient is infected with a suspected pathogen, bacteria, from the patient's tissues or fluids, are typically grown on agar to determine the identity of the pathogen. Many bacteria, however, even well-known species, do not grow well under laboratory conditions. FISH can be used to detect directly the presence of the suspect on small samples of patient's tissue.

FISH can also be to used compare the genomes of two biological species, to deduce evolutionary relationships. A similar hybridization technique is called a zoo blot. Bacterial FISH probes are often primers for the 16s rRNA region.

FISH is widely used in the field of microbial ecology, to identify microorganisms. Bio-films, for example, are composed of complex (often) multi-species bacterial organizations. Preparing DNA probes for one species and performing FISH with this probe allows one to visualize the distribution of this specific species within the bio-film. Preparing probes (in two different colors) for two species allows to visualize/study co-localization of these two species in the bio-film, and can be useful in determining the fine architecture of the bio-film.